Serwer ftp-->ubuntu

[Magik]

Witam

kolejny turecki problemik

uruchomilem

Kod: Zaznacz wszystko

sudo apt-get install vsftpd

nastepnie

Kod: Zaznacz wszystko

sudo gedit /etc/vsftpd.conf

# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone? vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=YES
#
# Run standalone with IPv6?
# Like the listen parameter, except vsftpd will listen on an IPv6 socket
# instead of an IPv4 one. This parameter and the listen parameter are mutually
# exclusive.
#listen_ipv6=YES
#
# Allow anonymous FTP? (Beware - allowed by default if you comment this out).
anonymous_enable=YES
#
# Uncomment this to allow local users to log in.
#local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
#write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format
#xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories. See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
#
# Debian customization
#
# Some of vsftpd's settings don't fit the Debian filesystem layout by
# default. These settings are more Debian-friendly.
#
# This option should be the name of a directory which is empty. Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem
# This option specifies the location of the RSA key to use for SSL
# encrypted connections.
rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key

wszystkie opcje mam zakomentowane hi, gdzie powienien usunac hash by konfiguracja wygladala mniej wiecej tak:
serwer nie startuje wraz z systemem
wymagane jest haslo i nazwa uzytkownika(i gdzie to ustawic)
zmienic katalog domyslny
prawo do downlaodu i uploadu plikow w katalogu ftp dla uzytkownikow


jezeli bedzie ustawiona opcja manualnego startu to serwer uruchamiam tak:

Kod: Zaznacz wszystko

sudo  /etc/init.d/vsftpd  start

i rozumiem, ze analogicznie wylaczam dajac

Kod: Zaznacz wszystko

sudo  /etc/init.d/vsftpd  stop

[Mike]

http://www.linuxhomenetworking.com/wiki/index.php/Quick_HOWTO_:_Ch15_:_Linux_FTP_Server_Setup

to by było na tyle

[JarekMk]

Coś ode mnie:

ProFTPd

Kod: Zaznacz wszystko

apt-get install proftpd

nano /etc/proftpd/proftpd.conf

[...]
UseIPv6 off
[...]

[...]
DefaultRoot /var/www
IdentLookups off
ServerIdent on "Serwer FTP działa"
[...]

w/w dodajemy na końcu pliku
chown nazwa_użytkownika.nazwa_użytkownika /var/www
Jesli chcemy tam katalog ftp robimy
mkdir -p /var/wwwftp
chmod 0777 /var/www/ftp
i wtedy w/w chown

Jeśli chcemy aby serwer był uruchamiany ręcznie ( domyślnie startuje wraz ze startem systemu ) kasujemy dowiązanie:
rm /etc/rc2.d/SXXproftpd
Gdzie XX to 2 liczbowa cyfra, ls -l /etc/rc2.d/ - i szukaj

Usługę startujemy tak: /etc/init.d/proftpd start / stop stopuje ją.
Logujemy się wpisując adres IP, login = nasza nazwa użytkownika, hasło = takie jak w systemie

Pzdr!

Autor postu otrzymał pochwałę

[Magik]

Niestety manuale dla poczatkujacych sa calkowicie nieczytelne i nie da sie za pomoca manuala w pierwszych tygodniach zdzialac samemu

Coś ode mnie:

wlasnie Jarek, dzieki wielkie za help'a, na pewno mniej dlubania niz przy pierwotnym projekcie i co najwazniejsze wszystko dziala:)

edit
a juz mialem podziekac mojemu Ubu za wspolprace i wrocic do Windy

[Nikt17]

Dosyć stary temat, ale może odswieżę, siedzę na ubuntu 8.10 pare dni.

nie zrozumialem tego

w/w dodajemy na końcu pliku
chown nazwa_użytkownika.nazwa_użytkownika /var/www
Jesli chcemy tam katalog ftp robimy
mkdir -p /var/wwwftp
chmod 0777 /var/www/ftp
i wtedy w/w chown

i mam problem. wyskakuje okno logowania a co ja mam tam wpisac? cos może źle zrobilem pomoże ktos?

#
# /etc/proftpd/proftpd.conf -- This is a basic ProFTPD configuration file.
# To really apply changes reload proftpd after modifications.
#

# Includes DSO modules
Include /etc/proftpd/modules.conf

# Set off to disable IPv6 support which is annoying on IPv4 only boxes.
UseIPv6 on
# If set on you can experience a longer connection delay in many cases.
IdentLookups off

ServerName "slimek"
ServerType standalone
DeferWelcome off

MultilineRFC2228 on
DefaultServer on
ShowSymlinks on

TimeoutNoTransfer 600
TimeoutStalled 600
TimeoutIdle 1200

DisplayLogin welcome.msg
DisplayChdir .message true
ListOptions "-l"
IdentLookups off
ServerIdent on
DenyFilter \*.*/

# Use this to jail all users in their homes
DefaultRoot /var/www

# Users require a valid shell listed in /etc/shells to login.
# Use this directive to release that constrain.
# RequireValidShell off

# Port 21 is the standard FTP port.
Port 21

# In some cases you have to specify passive ports range to by-pass
# firewall limitations. Ephemeral ports can be used for that, but
# feel free to use a more narrow range.
# PassivePorts 49152 65534

# If your host was NATted, this option is useful in order to
# allow passive tranfers to work. You have to use your public
# address and opening the passive ports used on your firewall as well.
# MasqueradeAddress 1.2.3.4

# This is useful for masquerading address with dynamic IPs:
# refresh any configured MasqueradeAddress directives every 8 hours
<IfModule mod_dynmasq.c>
# DynMasqRefresh 28800
</IfModule>

# To prevent DoS attacks, set the maximum number of child processes
# to 30. If you need to allow more than 30 concurrent connections
# at once, simply increase this value. Note that this ONLY works
# in standalone mode, in inetd mode you should use an inetd server
# that allows you to limit maximum number of processes per service
# (such as xinetd)
MaxInstances 30

# Set the user and group that the server normally runs at.
User proftpd
Group nogroup

# Umask 022 is a good standard umask to prevent new files and dirs
# (second parm) from being group and world writable.
Umask 022 022
# Normally, we want files to be overwriteable.
AllowOverwrite on

# Uncomment this if you are using NIS or LDAP via NSS to retrieve passwords:
# PersistentPasswd off

# This is required to use both PAM-based authentication and local passwords
# AuthOrder *mod_auth_pam.c mod_auth_unix.c

# Be warned: use of this directive impacts CPU average load!
# Uncomment this if you like to see progress and transfer rate with ftpwho
# in downloads. That is not needed for uploads rates.
#
# UseSendFile off

# Choose a SQL backend among MySQL or PostgreSQL.
# Both modules are loaded in default configuration, so you have to specify the backend
# or comment out the unused module in /etc/proftpd/modules.conf.
# Use 'mysql' or 'postgres' as possible values.
#
#<IfModule mod_sql.c>
# SQLBackend mysql
#</IfModule>

TransferLog /var/log/proftpd/xferlog
SystemLog /var/log/proftpd/proftpd.log

<IfModule mod_quotatab.c>
QuotaEngine off
</IfModule>

<IfModule mod_ratio.c>
Ratios off
</IfModule>


# Delay engine reduces impact of the so-called Timing Attack described in
# http://security.lss.hr/index.php?page=details&ID=LSS-2004-10-02
# It is on by default.
<IfModule mod_delay.c>
DelayEngine on
</IfModule>

<IfModule mod_ctrls.c>
ControlsEngine off
ControlsMaxClients 2
ControlsLog /var/log/proftpd/controls.log
ControlsInterval 5
ControlsSocket /var/run/proftpd/proftpd.sock
</IfModule>

<IfModule mod_ctrls_admin.c>
AdminControlsEngine off
</IfModule>

#
# Alternative authentication frameworks
#
#Include /etc/proftpd/ldap.conf
#Include /etc/proftpd/sql.conf

#
# This is used for FTPS connections
#
#Include /etc/proftpd/tls.conf

# A basic anonymous configuration, no upload directories.

# <Anonymous ~ftp>
# User ftp
# Group nogroup
# # We want clients to be able to login with "anonymous" as well as "ftp"
# UserAlias anonymous ftp
# # Cosmetic changes, all files belongs to ftp user
# DirFakeUser on ftp
# DirFakeGroup on ftp
#
# RequireValidShell off
#
# # Limit the maximum number of anonymous logins
# MaxClients 10
#
# # We want 'welcome.msg' displayed at login, and '.message' displayed
# # in each newly chdired directory.
# DisplayLogin welcome.msg
# DisplayFirstChdir .message
#
# # Limit WRITE everywhere in the anonymous chroot
# <Directory *>
# <Limit WRITE>
# DenyAll
# </Limit>
# </Directory>
#
# # Uncomment this if you're brave.
# # <Directory incoming>
# # # Umask 022 is a good standard umask to prevent new files and dirs
# # # (second parm) from being group and world writable.
# # Umask 022 022
# # <Limit READ WRITE>
# # DenyAll
# # </Limit>
# # <Limit STOR>
# # AllowAll
# # </Limit>
# # </Directory>
#
# </Anonymous>